Investigation of the Ga-Sb-S chalcogenide glass with low thermo-optic coefficient as an acousto-optic material

In this study, two series of Ga_xSb_40-xS₆₀ (x = 4, 6, 8, 10 mol%) and Ga_ySb₃₆S_64-y (y = 3, 5, 6 mol%) glasses were prepared and the relationship between their compositional and acousto-optic (AO) properties was investigated systematically for the first time. In the Ga_ySb₃₆S_64-y system, the AO figure of merit (M₂) increased as the Ga increased, and the maximum M₂ of the Ga₆Sb₃₆S₅₈ glass was 455.78 × 10^?18 s³/g, which is ～301 times greater than that of fused silica and ～2.5 times greater than that of As₂S₃ chalcogenide (ChG) glass at 1550 nm. However, its thermo-optic coefficients (dn/dT) varied greatly (32.1 × 10^?6 °C^?1–57.2 × 10^?6 °C^?1), and acoustic attenuations (α) at 10 MHz were high, from 5.446 dB/cm to 7.274 dB/cm. In the Ga_xSb_40-xS₆₀ glass system, the M₂ value and α at different ultrasonic frequencies gradually decreased with the improvement of Ga. Compared with the Ga_ySb₃₆S_64-y system, the Ga_xSb_40-xS₆₀ glass system had lower α (at 10 MHz) and dn/dT, which are 5.001 dB/cm–5.563 dB/cm and 17.3 × 10^?6 °C^?1–55.6 × 10^?6 °C^?1, respectively. These results provide a significant reference for the further development of novel ChG glasses and help expand their application fields.     

Wear resistance and hardness properties of TiB2– Fe coating developed on AISI 1020 steel by tungsten inert gas (TIG) cladding

The present work is attempted to improve the microhardness and wear properties of AISI 1020 steel by depositing TiB₂–Fe composite coating using tungsten inert gas (TIG) cladding. In this study, different compositions of TiB₂–Fe paste form were preplaced on the substrate plates and then TIG heat input was applied to deposit hard composite coating layer. The main objective of the present work was to explore the influence of TIG input current as well as iron content on the microstructure and surface properties of deposited coatings. Microhardness, microstructural and phase characterization of the coating have been done by the Vickers microhardness tester, scanning electron microscope (SEM), Energy dispersive spectroscopy (EDS) and X-ray diffractrometer (XRD). The results showed that the microhardness of the TiB₂–Fe coating was strongly influenced by the composition of the coating materials as well as the TIG processing current. The microhardness increases with decreasing Fe contents in the coating materials with constant processing current (90 A) as well as it also increases with decreasing processing current with the fixed composition of coating materials (80TiB₂–20Fe). The maximum average microhardness found was 3082 HV_0.1 for the coating of 100TiB₂–0Fe composition ratio and 90 A processing current which was about 18 times higher than that of the substrate average microhardness value (163 HV_0.1). Average wear rate evaluated by considering weight loss of the TIG cladded samples using pin on disc tribometer by the sliding distance of 864 m and 20 N normal loads. The wear results also showed that the coating contains 100 wt% of TiB₂ (0 wt% of Fe) exhibited lower rate of wear 6.74 × 10^?8 g/Nm which is about 24 times lower as compared to AISI 1020 mild steel wear rate (166.31 × 10^?8 g/Nm).     

Thermomechanical stability and inelastic energy dissipation as durability criteria for fuel cell gas diffusion media with pre-assembly effects

In this article, pre-assembly hot-press pressure and thermal expansion effects in gas-diffusion layers (GDLs) are addressed to explore the practicalities of the constitutive model reported in the companion article. A facile technique is proposed to include deformation history dependent residual strain effects. The model is implemented in the numerical environment and compared with widely followed conventional models such as isotropic and orthotropic material models. With the normal and accelerated thermal expansion effects no significant variation in stresses or strains is reported with the compressible GDL model in contrast to the conventional incompressible form of the GDL model. The present work identifies the critical differences with advanced and extended variants of the model along with conventional GDL material models in terms of planar stress/strain distribution and the membrane response. Finally, the model is simulated for micro-cyclic stress loads of varying amplitudes that imitate the real working conditions of fuel cell. The inelastic energy dissipation in GDLs is predicted using the proposed model, which is utilized further to distinguish the safe (elastic) and unsafe (inelastic shakedown) operating limits. The inelastic collapse of GDLs is shown to be a active function of high amplitude micro-cyclic load with high initial clamping load.     

Influence of pulse-jet cleaning pressure on performance of compact dust collector with pleated filter operated in clean-on-time mode

To operate a bag filter continuously, pulse-jet cleaning of dust particles from the filter medium is commonly required, and the pulse-jet pressure significantly affects the filter performance. In this study, the accumulation structure of residual dust particles inside and on the surface of a filter medium at different pulse-jet pressures was investigated by constructing a simple model, and the influence of the dust structure on the filter performance was clarified. Using a simple model, we determined the effective ratio of filtration area β, which represents the ratio of the filterable area to the total filtration area, the true resistance coefficient due to the primary dust layer ζ_p’ thinly deposited on the filter surface, and the true resistance coefficient inside the filter media itself ζ_f’_. The effective ratio of filtration area β decreased with operation time for all pulse-jet pressures; however, it maintained a high value when the pulse-jet pressure was high. The validity of β analyzed by the model was verified using two different methods, and the results showed good agreement, indicating that the model is effective in identifying real conditions. The true resistance coefficient due to the primary dust layer ζ_p’ decreased as the pulse-jet pressure increased; however, the true resistance coefficient inside the filter media itself ζ_f’ was the highest at 0.5 MPa. In addition, the dust collection efficiency was different at each pulse-jet pressure, which was considered to be caused by the difference in the dust particle accumulation structure.     

水-油连续螺旋折流板换热器热力性能研究

利用计算流体力学(Computational Fluid Dynamic, CFD)方法，针对连续螺旋折流板换热器建立物理模型和数学模型，在管侧介质为水和壳侧介质为原油条件下，研究不同原油流量及螺旋角对螺旋折流板换热器内部流场、换热性能及阻力性能的影响，并拟合了水油换热时螺旋折流板换热器的Nu、f与Re的关联式。结果表明：22°螺旋角的螺旋折流板换热器与其它较小螺旋角换热器对比，壳侧压降和换热系数逐渐减小，综合换热性能最佳。通过对壳侧原油为层流状态下的阻力系数和对流换热系数关系式进行拟合，更好地指导水-油连续螺旋折流板换热器的热力设计。     

Mechanical behavior of YSZ coatings co-deposited with Al and Ag on AISI 316L via RF sputtering

This article presents nanohardness, coefficient of friction (COF), and wear of Yttria-stabilized zirconia coatings (YSZ) deposited on 316L steel substrates and co-deposited with Al and Ag. YSZ coatings were deposited via RF sputtering reactive phase technique. It is widely known that the RF sputtering technique produces stoichiometric coatings with high homogeneity and density. The average thickness of the coatings was 200 nm, and the X-ray diffraction study (XRD) showed the formation of alumina alpha (α-Al₂O₃) and metallic silver in the YSZ coatings deposited with Al and Ag, respectively. The mechanical properties were evaluated by means of nanoindentation, and the wear resistance was studied with pin-on-disk technique. The addition of Ag to the YSZ coatings led to decreased hardness, while the YSZ coatings deposited with Al presented an increased hardness. Finally, YSZ coatings deposited with aluminum and silver had the lowest friction coefficient, while Ag-YSZ coatings had a COF very similar to that obtained in YSZ coatings. The wear resistance test showed that YSZ coatings deposited with Al had lower volume loss compared to YSZ coatings deposited with Ag. The wear mechanism in the deposited coatings is analyzed.     

Strain mediated enhancement in magnetoelectric properties of sonochemically synthesized piezoelectric and piezomagnetic composites

Materials with magneto-electric (ME) properties are of great importance because of their demand in electronic industries. Three dimensional nano-particles of the ME-composites having the general formula (1-x)CoCr_0.3Fe_1.7O₄(CCFO)+(x)BaTiO₃(BTO) (x = 0.0, 0.2, 0.4, 0.6, 0.8 and 1.0) were obtained by comprising the piezoelectric-BTO and piezomagnetic-CCFO phases. The individual phases of CCFO and BTO were synthesized separately by ultrasonic irradiation assisted sonochemical and sol-gel routs. X-ray diffraction patterns (XRD) confirmed the well-crystalline nature of both the phases. BTO and CCFO phases were under tensile strain as confirmed by the variation in lattice constants with varying proportion of BTO and CCFO. An energy-dispersive X-ray spectroscopy spectrum confirmed the phase purity of the samples and stoichiometric concentration of elements. Magnetic properties were investigated by M ? H loop measurements and dielectric properties by using RF impedance analyzer. Dielectric constant increased with the increasing percentage of BTO. The maximum value of ME coefficient (24.7 mV/cm?Oe) is observed for the 60%CCFO+40%BTO sample. The obtained results were discussed in the light of grain size, strain and the basic properties of the individual phases. The prepared materials can be applicable in electronic devices where high magneto-electric coefficient is desirable.     

An experimental study of forced convective heat transfer for fully developed Al 2 O 3 –water nanofluid in an annulus tube

Nanofluids have been known as practical materials to ameliorate heat transfer within diverse industrial systems. The current work presents an empirical study on forced convection effects of Al₂O₃–water nanofluid within an annulus tube. A laminar flow regime has been considered to perform the experiment in high Reynolds number range using several concentrations of nanofluid. Also, the boundary conditions include a constant uniform heat flux applied on the outer shell and an adiabatic condition to the inner tube. Nanofluid particle is visualized with transmission electron microscopy to figure out the nanofluid particles. Additionally, the pressure drop is obtained by measuring the inlet and outlet pressure with respect to the ambient condition. The experimental results showed that adding nanoparticles to the base fluid will increase the heat transfer coefficient (HTC) and average Nusselt number. In addition, by increasing viscosity effects at maximum Reynolds number of 1140 and increasing nanofluid concentration from 1% to 4% (maximum performance at 4%), HTC increases by 18%.     

Process parameters influence on zone refining and thermodynamics analysis of 1,2-diphenylethane

Effective distribution coefficients of 9 impurities in 1,2-diphenylethane have been calculated by directional crystallization under different ambient frozen temperature. The effect of varied zone size, temperature difference between the melt and ambient frozen environment, number of zone on purity of 1,2-diphenylethane have been also investigated during the process of zone refining. The results indicate that the product purity in the intermediate purified region with varied zone size is higher 0.04%-0.2% than that with constant zone size. The product purity increases with temperature difference between the melt and ambient frozen environment. The appropriate temperature difference is adopted 50℃. The product purity in the intermediate region of sample bar with 2 molten zones is higher 0.05%-0.43% than that with 1 molten zone. In addition, the change of enthalpy and entropy between impurities and 1,2-diphenylethane have been determined.